Installation Manual For Lima Waterfall and Rainfall Shower Set

Home > Lima Waterfall and Rainfall Shower Set Installation Instruction

Lima Waterfall and Rainfall Shower Set with Thermostatic Mixer Valve

The Lima Waterfall and Rainfall Shower Set with Thermostatic Mixer Valve comes with durable ceramic valves installed in it that ensure zero water leaks. This amazing faucet is manufactured using superior quality raw material and works at a water temperature of 90 degrees. What makes it distinguishable is its elegant finish and adherence to the best quality standards. It is tested at 1.6Mpa water pressure for quality assurance.

Lima Waterfall and Rainfall Shower Set with Thermostatic Mixer Valve Features:

Brand Name: BathSelect

Model Number: BZ-5609

Type: Thermostatic Shower Set

Installation: Wall Mount

Style: Contemporary

Finish: Chrome

Shower Head Function: Rainfall, Waterfall

Number of Handles: Three Handles

Valve Type: Ceramic Valve

Faucet Spout & Body Material: Brass

Faucet Handle Material: Zinc Alloy

Shower Head Size: 21.6" * 9" (550*230mm)

Handheld Shower Material: A grade ABS

Shower HeadMaterial: Stainless Steel

Shower Head Material: Brass

Flow Rate: 2 .5 GPM

Milan Juno 24"LED Rain Shower Head Thermostatic Shower Valve Set

BathSelect® Manufacturer Warranty Information

Before you begin, please read the installation instructions below. Observe all local building and safety codes.
Unpack and inspect the product for any shipping damages. If you find damages, do not install.
Please note all showers must be installed by a professional and certified plumber otherwise warranty might be voided.

shower

1. Open the top cover and drill according to the marked position.

Mark by the position of the four holes.
Take care to avoid wires and pipes to prevent damage.
Be sure to confirm that the four holes are on the same horizontal line

2. Two inlet fittings are connected to the pipe joint of the wall; then the nut, expansion screw, and inlet pipe are connected.

3. Reinstall the top cover.

Shower Body-Jet Installation

Step 1	shower	Step 2	shower
Step 3		Step 4
Step 1: Multiple Bodyspray Installation • Water Supply • Nipple Mamelon Nipple • Pressure Balancing Loop 1. Route the water supply lines. 2. If installing more than one bodyspray off the same supply line, construct a pressure balancing loop. Locate a tee along the loop at each bodyspray installation location. 3. Do not strap the pipes at this time. Single Bodyspray Installation • Nipple Mamelon Nipple 1. Route the water supply line. 2. Install an elbow to the end of the supply pipe at the bodyspray installation location. Step 2: Install the Plaster Guard • Elbow (or Tee) • Install the plaster guard Set Piping Depth Align mark with the front of the stud face • Thin Wall Align mark with the front of the stud face • Standard Wall install the plaster guard. Push until the plaster guard is snug against the face of the elbow (or tee).		Step 3: 1. Install the water-resistant wallboard. 2. Cut out a 4" (10.2 cm) to 4-1/4" (10.8 cm) square at each the installation location. 3. Install the finished wall material. Step 4: • Escutcheon • Leak Shield • Adapter • Extension • Socket Wrench With Bit • Screw • Waterway Passage 1. Insert the escutcheon into the rough opening. The double ribs of the leak shield should be facing up. 2. If the leak shield makes contact with the elbow: Enlarge the hole in the back of the leak shield to 1-1/4" (3.2 cm). 3. Thread the adapter onto the nipple using the provided 0.4" bit, 11 mm or 7/16" socket, extension and socket wrench. Use masking tape to hold the bit in place, as the bit could fall off and cause damage. IMPORTANT! The escutcheon should sit loosely at this point. If it is tight against the wall, use a longer pipe nipple. 4. Align the groove in the waterway with the double ribs on the leak shield. 5. Press the waterway into place over the adapter. Secure the waterway to the adapter with the screw provided. 6. Verify that the escutcheon does not turn or shift.